# $Id: pnpdump.c,v 1.15a 1998/05/25 17:22:16 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER # # Trying port address 0203 # Trying port address 020b # Board 1 has serial identifier be 00 00 00 02 04 00 79 05 # Board 2 has serial identifier 30 ff ff ff ff 37 42 63 0e # (DEBUG) (READPORT 0x020b) (ISOLATE PRESERVE) (IDENTIFY *) # Card 1: (serial identifier be 00 00 00 02 04 00 79 05) # Vendor Id AKY0004, Serial Number 2, checksum 0xBE. # Version 1.0, Vendor version 0.0 # ANSI string -->ASKEY 56K Plug&Play Modem <-- # # Logical device id AKY0004 # Device support I/O range check register # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE AKY0004/2 (LD 0 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 (IO 0 (BASE 0x03e8)) # IRQ 9. # (INT 0 (IRQ 9 (MODE +E))) # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x03f8)) # IRQ 4. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02f8)) # IRQ 3. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02e8)) # IRQ 3. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0100)) # IRQ 3, 5, 7, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0100)) # IRQ 4, 5, 7, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0100)) # IRQ 3, 5, 7, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0100)) # IRQ 4, 5, 7, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 4 (MODE +E))) # End dependent functions (ACT Y) )) # End tag... Checksum 0x00 (OK) # Card 2: (serial identifier 30 ff ff ff ff 37 42 63 0e) # Vendor Id CSC4237, No Serial Number (-1), checksum 0x30. # Version 1.0, Vendor version 0.1 # ANSI string -->CRD4237B-3 <-- # # Logical device id CSC0000 # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CSC4237/-1 (LD 1 # ANSI string -->WSS/SB <-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type A (DMA 0 (CHANNEL 0)) # Next DMA channel 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type A (DMA 1 (CHANNEL 3)) # IRQ 5. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0534 # Maximum IO base address 0x0534 # IO base alignment 4 bytes # Number of IO addresses required: 4 (IO 0 (BASE 0x530)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 8 bytes # Number of IO addresses required: 4 (IO 1 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0220 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 2 (BASE 0x0220)) # Start dependent functions: priority acceptable # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type A # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type A # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0534 # Maximum IO base address 0x0ffc # IO base alignment 4 bytes # Number of IO addresses required: 4 # (IO 0 (BASE 0x0534)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 8 bytes # Number of IO addresses required: 4 # (IO 1 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0260 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 2 (BASE 0x0220)) # Start dependent functions: priority functional # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type A # (DMA 0 (CHANNEL 0)) # IRQ 5, 7, 9, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0534 # Maximum IO base address 0x0ffc # IO base alignment 4 bytes # Number of IO addresses required: 4 # (IO 0 (BASE 0x0534)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 4 # (IO 1 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0300 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 2 (BASE 0x0220)) # End dependent functions (ACT Y) )) # # Logical device id CSC0001 # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CSC4237/-1 (LD 2 # ANSI string -->GAME <-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0200 # Maximum IO base address 0x0200 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0200)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0208 # Maximum IO base address 0x0208 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0208)) # End dependent functions (ACT Y) )) # # Logical device id CSC0010 # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CSC4237/-1 (LD 3 # ANSI string -->CTRL <-- # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0120 # Maximum IO base address 0x0ff8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0120)) (ACT Y) )) # # Logical device id CSC0003 # Device supports vendor reserved register @ 0x3a # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE CSC4237/-1 (LD 4 # ANSI string -->MPU <-- # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # IRQ 9. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 9 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0330 # IO base alignment 8 bytes # Number of IO addresses required: 2 (IO 0 (BASE 0x330)) # Start dependent functions: priority acceptable # IRQ 9, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 9 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0360 # IO base alignment 8 bytes # Number of IO addresses required: 2 # (IO 0 (BASE 0x0330)) # Start dependent functions: priority functional # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x03e0 # IO base alignment 8 bytes # Number of IO addresses required: 2 # (IO 0 (BASE 0x0330)) # End dependent functions (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY)